What Is CAN/ULC-S705.2 & Caliber Certified Spray Foam Installation in Ontario? (2026 Daily Work Record & Building Inspector Guide)

What Is CAN/ULC-S705.2 & Caliber Certified Spray Foam Installation in Ontario? (2026 Daily Work Record & Building Inspector Guide): 2026 Ontario Overview & Code Essentials
When you hire a contractor for basement spray foam insulation, custom home envelope insulation, or commercial warehouse spray foam in Toronto, the GTA, or anywhere in Ontario, your municipal building inspector does not just look at the foam on the wall—they look for an official CAN/ULC-S705.2 Daily Work Record and Jobsite Warranty Sticker stapled to the framing. Because spray polyurethane foam is manufactured right on your jobsite from two liquid chemical drums (A-side polymeric MDI and B-side polyol blend), the Ontario Building Code treats the installer on the spray gun as a live chemical manufacturer.
If an unlicensed handyman or uncertified rig sprays your basement, attic, or commercial building without a valid CAN/ULC-S705.2 license number and third-party Caliber Certified registration, municipal building officials in Toronto, Mississauga, Brampton, Vaughan, Markham, Oakville, and Hamilton will issue an immediate Order to Comply (Red Tag)—often forcing the homeowner or general contractor to strip the uncertified foam down to bare studs. At Sprayfoam Solutions Toronto Inc. ((647) 333-3626), every rig is operated by Caliber Certified (CAN/ULC-S705.2 Licensed) Installers spraying verified CCMC-approved low-VOC HFO chemicals. Check your certified installation price in 60 seconds at spfsolutions.ca/price-chat and claim a $250 Credit on Your Estimate with No Site Visit Required.
Every residential and commercial scope below includes a licensed Caliber Certified installer, on-site core testing, and your official CAN/ULC-S705.2 Daily Work Record:
- 3.5"–5.5" CAN/ULC-S705.1 2 lb Closed-Cell
- Includes Signed CAN/ULC-S705.2 Daily Work Record & Jobsite Sticker + $250 Estimate Credit
- OBC SB-12 Envelope + Acoustic Ceilings
- Caliber Certified Lot Tracking, Core Density Log & CCMC Sheet
- Passes First Inspection
- 2 lb Closed-Cell SPF + Optional 18-Mil IFTI DC315 (CAN/ULC-S124)
- Complete Architect & Municipal Inspector QA Submittal Binder
Why Ontario Municipal Building Inspectors Demand a CAN/ULC-S705.2 Daily Work Record (2026 Code Table)
Unlike fiberglass batts or rigid XPS foam boards—which are manufactured in a factory and stamped with a fixed R-value before arriving at a lumberyard—2 lb closed-cell spray polyurethane foam only achieves its rated R-6.0 per inch, Class 1 vapour barrier rating (<60 ng/Pa·s·m²), and dimensional stability when sprayed within strict temperature, pressure, substrate-moisture, and pass-thickness limits. Here is what your Ontario municipal building inspector checks on every CAN/ULC-S705.2 Daily Work Record before signing your framing/insulation permit:
| Mandatory CAN/ULC-S705.2 Inspection Item | What Our Caliber Certified Installer Records On Site | Ontario Building Code / ULC Requirement | What Happens If Missing (Uncertified Crew) | Net Cost Impact With Our Crew |
|---|---|---|---|---|
1. Installer License & Caliber ID | Lead sprayer’s active CAN/ULC-S705.2 License # & Caliber Certified photo ID number | Mandatory under Ontario Building Code & CAN/ULC-S705.2 | Automatic Failed Inspection (Inspector rejects unsigned foam) | $0 Included on every job |
2. Chemical System & CCMC Evaluation # | Exact resin brand ( BASF Walltite Eco v.3, Huntsman, JM) + CCMC # | Must match CAN/ULC-S705.1 tested product listing | Inspector halts drywall until chemical CCMC report is proven | $0 Included in permit binder |
3. A-Side & B-Side Drum Lot Numbers | Batch lot numbers & expiry dates from both 55-gallon chemical drums | Full chemical traceability from factory to wall cavity | Zero manufacturer warranty if off-ratio or expired drums used | $0 Included on Daily Work Record |
4. Substrate Moisture & Ambient Temp | Pin-meter moisture reading ( <18% on wood/concrete) + surface/air temps | Prevents foam blistering, shrinkage, or bond delamination | Foam pulls away from damp concrete or cold steel in winter | $0 Included pre-spray check |
5. On-Site Core Density & Lift Depth | Core-cut sample weight ( ≥1.8–2.2 lb/ft³) + max 2.0" pass lift verification | Verifies true closed-cell density & stops exothermic scorching | Over-thick single passes char inside or shrink off studs | $0 Included QA verification |
CAN/ULC-S705.1 (Material Standard) vs. CAN/ULC-S705.2 (Installation Standard) Explained
Homeowners, architects, and general contractors reviewing our 2026 Ontario Basement Insulation Code Guide often ask about the difference between the two sibling Canadian spray foam standards referenced in the 2026 Ontario Building Code:
CAN/ULC-S705.1(Standard for Thermal Insulation — Spray Applied Rigid Polyurethane Foam, Medium Density — Material Specification): This is the laboratory material standard evaluated by the Canadian Construction Materials Centre (CCMC). To earn aCAN/ULC-S705.1listing, a chemical system (such as BASF Walltite® Eco v.3, Huntsman Building Solutions [Icynene/Demilec], Johns Manville & other approved CCMC spray foam chemicals — Low-VOC HFO Blown) must prove an aged long-term thermal resistance (LTTR) of ~R-6.0 per inch, compressive strength >15–25 PSI, air permeance<0.02 L/s·m², and water vapour permeance<60 ng/Pa·s·m²(Class 1 / Type II Vapour Retarder) at ~2 inches depth.CAN/ULC-S705.2(Standard for Thermal Insulation — Spray Applied Rigid Polyurethane Foam, Medium Density — Application): This is the mandatory field installation standard. It governs how the licensed contractor prepares the substrate, masks the building, sets proportioner hose temperatures and pressures, limits each spray pass to a maximum of 2.0 inches (50 mm) with cooling intervals between lifts, tests core density on site, ventilates the work zone for 24 hours, and leaves a signed Daily Work Record and Jobsite Label for the municipal building inspector.
![5" (R31) of 2lb closed-cell spray foam on a sloped cathedral ceiling roof deck in Pickering (Rougemount & Dunbarton) [JOB-2025-10-07-01]](/images/jobs/cathedral-ceiling-spray-foam/cathedral-ceiling-spray-foam-toronto-job-2025-10-07-01-1.webp)
How Caliber Third-Party Auditing Protects Ontario Homeowners, Custom Builders & General Contractors
In Canada, an installer cannot simply declare themselves compliant with CAN/ULC-S705.2. Under the standard, every applicator and contractor company must be licensed and field-audited by an accredited third-party certification organization under the Standards Council of Canada framework. Sprayfoam Solutions Toronto Inc. is Caliber Certified under the accredited Caliber Third-Party Certification Standard—meaning our installers, proportioner rigs, and jobsite documentation are independently audited to protect your property:
![2" (R12) of 2lb closed-cell spray foam encapsulating sheet-metal attic HVAC ductwork in Ajax & Whitby (Brooklin) [JOB-2020-04-18-01]](/images/jobs/closed-cell-spray-foam/closed-cell-spray-foam-toronto-job-2020-04-18-01-7.webp)
Moisture, temperature & chemical batch verification.
Digital pin hygrometer & infrared surface thermometer.
Prevents off-ratio foam, shrinkage & blistering.
Before pulling the trigger, our Caliber Certified installer verifies that concrete, wood, or steel substrates are clean, frost-free, and below 18% moisture content, selects the winter/summer chemical formulation matching the exact substrate temperature, and logs both A-side and B-side drum lot numbers on your Daily Work Record.
6 Critical CAN/ULC-S705.2 Field Rules That Prevent Spray Foam Failure, Odours & Failed Inspections
Whenever you read a news story about a spray foam job that smelled bad, shrank away from wood studs, or was red-tagged by an Ontario building official, 100% of those failures trace back to an uncertified contractor violating one of these six mandatory CAN/ULC-S705.2 field rules:
- 1. Strict Adherence to the 2.0-Inch (50 mm) Maximum Single-Pass Lift Rule: Closed-cell polyurethane foam cures via an exothermic (heat-generating) reaction. If an impatient sprayer blasts 4 or 5 inches of closed-cell foam in a single pass into a cathedral ceiling or garage ceiling, core temperatures exceed
150°C—scorching the interior foam, causing shrinkage cracks, and trapping amine odours. Our Caliber Certified crews strictly enforce≤2.0"lifts with mandatory cooling intervals. - 2. Winter Substrate Temperature Formulations (
Wintervs.Regularvs.SummerResin Grades): In an unheated Toronto basement or custom home in January (-10°C to -20°C), spraying summer-grade resin onto freezing concrete causes brittle "popcorn" delaminating bond lines. Under CAN/ULC-S705.2, we carry temperature-matched winter/arctic chemical grades and use heated drum blankets and 300-foot heated proportioner hoses. - 3. Mandatory 1.5-Inch Concrete Stand-Off Behind Framed Basement Studs: To achieve continuous insulation and prevent wood rot on below-grade foundations (see our 2026 Basement Spray Foam Cost Guide), framing should stand
1" to 1.5"off the concrete wall so closed-cell foam forms an unbroken monolithic blanket behind and between every stud. - 4. High-CFM Negative-Pressure Exhaust Ventilation & Canadian OHSA Safety: During application, we isolate the work zone with polyethylene containment, run industrial exhaust fans ducted directly outside to maintain negative air pressure, and equip sprayers with supplied-air respirators in full compliance with Canadian CCOHS and Ontario Ministry of Labour (OHSA) regulations.
- 5. Standard 24-Hour Occupancy & Trade Re-Entry Window: Once spraying is complete and negative-pressure ventilation runs, homeowners and other trades observe the standard 24-hour re-entry window. Because we exclusively spray low-VOC HFO-blown CCMC-evaluated chemicals at an exact
1:1computerized proportioner ratio, the cured foam at 24 hours is chemically stable, fully cured, and odourless. - 6. Mandatory Thermal Barrier Protection (
1/2"Drywall or Certified18-Mil DC315): Under Ontario Building Code Section 9.10.17.10 (Residential) and Section 3.1.4.2 (Commercial), cured spray foam must be covered by a 15-minute thermal barrier—either standard1/2"gypsum drywall or, where foam remains exposed in mechanical rooms, warehouses, or crawl spaces, 18 mils WFT (12 mils DFT) of certified IFTI DC315 intumescent thermal barrier coating.
![5" (R31) of 2lb closed-cell spray foam on a sloped cathedral ceiling roof deck and 3.5" (R22) on exterior walls in Oshawa & Clarington [JOB-2025-10-01-01]](/images/jobs/cathedral-ceiling-spray-foam/cathedral-ceiling-spray-foam-toronto-job-2025-10-01-01-4.webp)
Caliber Certified (CAN/ULC-S705.2 Licensed) Contractor vs. Uncertified Spray Foam Quotes (2026 Comparison)
Before accepting a suspiciously cheap spray foam quote from an unverified classified-ad operator, compare what a Caliber Certified (CAN/ULC-S705.2 Licensed) contractor delivers versus an uncertified crew in our 2026 Ontario Spray Foam Cost Guide:
| Verification & Compliance Metric | Sprayfoam Solutions Toronto Inc. (Caliber Certified) | Uncertified / Unlicensed "Cash" Rig Operator | Fiberglass Batts + 6-Mil Polyethylene Sheet |
|---|---|---|---|
Installer License Standard | Caliber Certified & CAN/ULC-S705.2 Licensed | None(Cannot legally sign Daily Work Record) | No license required(High air-leakage risk) |
CAN/ULC-S705.2 Daily Work Record | Included — Signed Sticker + PDF Permit Binder | Missing — Triggers Municipal Inspector Red Tag | N/A — Inspector checks poly tape & staples |
Approved Chemical Systems | BASF Walltite Eco v.3, Huntsman, JM(CCMC Listed) | Often grey-market, expired, or non-CCMC drums | Standard R-20 / R-24 fiberglass batts |
Class 1 Vapour Barrier(<60 ng) | Certified at ≥2.0" depth(No 6-mil poly needed) | Rejected by inspector without S705.2 worksheet | Requires separate hand-taped 6-mil poly sheet |
Insurance & WSIB Protection | $5,000,000 Liability Insurance + Active WSIB | Often uninsured or lapsed coverage | Varies by drywall/framing contractor |
Same-Week Caliber Certified Dispatch Across Toronto & the GTA ($0 Travel Fee)
Every mobile proportioner rig in our fleet is staffed by Caliber Certified (CAN/ULC-S705.2 Licensed) spray foam installers and equipped with computerized ratio-monitoring proportioners, digital moisture meters, and negative-pressure ventilation fans. We charge $0 Travel Fee across Toronto, Mississauga, Brampton, Vaughan, Markham, Oakville, Burlington, Hamilton, Pickering, Ajax, Whitby, Oshawa, Richmond Hill, Newmarket, Milton, and Barrie.

We confirm your municipal Ontario Building Code R-value target (R-20, R-24, R-31, or R-60) and schedule around your rough-in inspections.

Our licensed installer verifies <18% substrate moisture, logs chemical batch lots, masks the site, and starts negative-pressure exhaust fans.

Application of CAN/ULC-S705.1 2 lb closed-cell foam in ≤2.0" lifts, followed by on-site core-density and depth-pin verification.

We shave stud faces flush, vacuum the floor clean, post your signed CAN/ULC-S705.2 Daily Work Record on site, and email your PDF permit pack.
Frequently Asked Questions: CAN/ULC-S705.2 & Caliber Certified Spray Foam in Ontario
A CAN/ULC-S705.2 Daily Work Record (often called a daily worksheet or jobsite sticker) is a mandatory legal compliance document required under the Ontario Building Code whenever medium-density 2 lb closed-cell spray polyurethane foam (CAN/ULC-S705.1) is installed in a home or commercial building. Completed on site by a Caliber Certified (CAN/ULC-S705.2 Licensed) installer from Sprayfoam Solutions Toronto Inc. ((647) 333-3626 • spfsolutions.ca/price-chat), it records the installer’s license number, CCMC evaluation number, chemical batch lot numbers, substrate moisture, core density, and installed thickness so the municipal inspector can pass your insulation permit.
CAN/ULC-S705.1 is the material standard that tests the physical properties of medium-density 2 lb closed-cell spray foam in a laboratory (verifying ~R-6.0/inch thermal resistance, <0.02 L/s·m² air barrier performance, and <60 ng/Pa·s·m² Class 1 vapour barrier rating). CAN/ULC-S705.2 is the field installation standard that governs how licensed, third-party audited installers prepare the site, spray in ≤2.0" lifts, test core density, ventilate the work zone, and document the installation on site.
Caliber Certified means the spray foam contractor and its individual sprayers are licensed, trained, and field-audited under the accredited Caliber third-party certification body in accordance with CAN/ULC-S705.2. When you hire Sprayfoam Solutions Toronto Inc., every installer carries an active photo ID license card, uses calibrated proportioner rigs, and issues genuine Caliber-registered CAN/ULC-S705.2 Daily Work Records accepted by every municipal building department in Ontario.
No—$0 extra. Every residential basement, attic, garage, custom home, and commercial project completed by Sprayfoam Solutions Toronto Inc. ((647) 333-3626) includes our signed CAN/ULC-S705.2 Daily Work Record, physical Jobsite Warranty Sticker stapled near your electrical panel, and a digital PDF copy emailed to you or your general contractor. Check your turnkey price in 60 seconds at spfsolutions.ca/price-chat and claim a $250 Estimate Credit.
We exclusively install CCMC-evaluated, low-VOC HFO-blown CAN/ULC-S705.1 medium-density 2 lb closed-cell systems—including BASF Walltite® Eco v.3, Huntsman Building Solutions (Icynene/Demilec), Johns Manville & other approved CCMC spray foam chemicals (learn more on our Approved Spray Foam Chemicals Guide). Each drum lot number is recorded directly on your Daily Work Record for 100% manufacturer warranty traceability.
When A-side and B-side polyurethane chemicals react, they generate exothermic heat. Spraying more than 2.0 inches (50 mm) in a single pass traps excessive heat inside the foam core, which can cause internal charring, blistering, dimensional shrinkage away from studs, or lingering odours. By spraying in controlled ≤2.0" lifts with cooling intervals between passes, our Caliber Certified crews achieve a dense, uniform 2.0 lb/ft³ cell structure from R-21 (3.5") up to R-60 (10").
Under CAN/ULC-S705.2 and Canadian CCOHS guidelines, homeowners, pets, and unmasked sub-trades vacate the work area during application and re-enter after the standard 24-hour ventilation window. During application, we exhaust the work zone outdoors using high-CFM negative-pressure fans. Once cured at the 24-hour mark, low-VOC HFO closed-cell spray foam is chemically stable, fully cured, and odourless.
If your municipal building inspector issued an Order to Comply because exposed foam lacks a thermal barrier under Ontario Building Code Section 9.10.17.10 or 3.1.4.2, or if you need certified CAN/ULC-S705.2 spray foam installed for an upcoming inspection, call Sprayfoam Solutions Toronto Inc. at (647) 333-3626 or visit spfsolutions.ca/price-chat for 48-hour GTA inspection rescue and a $250 Credit on Your Estimate.
Select a technical guide, service hub, or GTA municipality below for local Ontario Building Code specs and same-week dispatch:






